QNAP Club Italia

PiaNi ha scritto: ↑21 ago 2024, 16:49 E' cambiata la password si default di Admin in caso di reset password.
Non è più il mac address.

[Security Updates]
- Applied multiple security updates to further enhance system security.

[New Features]
System
- Starting from QTS 5.2.2, certain QTS NAS models now also support the QuTS hero operating system. After updating to QTS 5.2.2, you can switch to QuTS hero by reinitializing the NAS. Applicable NAS models: TS-464U, TS-464U-RP, TS-1264U-RP, TS-464eU, TS-864eU, TS-864eU-RP, TS-i410X, and TS-410E.

[Fixed Issues]
- Fixed an issue where Safari users could not see the capacity of a connected external device in "Desktop > Task Bar > External Device".
- Addressed an issue on the TS-877XU where "Desktop > Task Bar > More > About" would display the wrong device model name if ECC memory modules were installed.
- Fixed an issue where for certain expansion unit models, under certain circumstances a healthy disk on the expansion unit might incorrectly display a "Not Exist" status in "Storage & Snapshots > Storage > External Storage > External Storage Device Management".
- Resolved an issue for some users where after performing NAS migration under certain conditions, storage pools from the old NAS would display an "Error" status on the new NAS.
- Fixed an issue where if a shared folder's name contained certain special characters, the system would fail to record a corresponding log when the shared folder was accessed via Samba.
- Fixed an issue for some users where Control Panel could not display domain users in "Privilege > Users".
- Fixed a French translation issue in the Desktop Notice Board.
- Fixed an issue where after a firmware update, the system might mistakenly display an event log warning that the currently installed version of Advanced Network Driver was not supported.

jim27 ha scritto: ↑21 nov 2024, 12:56 Buongiorno, non aggiornate alla 5.2.2 i 253D, infatti come scritto sopra da @ninoger62 rimane in loading permanente, e la 5.2.2 e' stata rimossa da Qnap per i 253D. Per risolvere il problema dovete reinstallare da console ssh la 5.2.1
Fatto da me personalmente per un mio cliente
Spero possa essere d'aiuto
Saluti e Salute

lucam1970 ha scritto: ↑26 nov 2024, 15:26 E tanto per semplificarci la vita, oggi Qnap fa uscire una nuova versione 5.1.9, ovvero tre step indietro rispetto alla 5.2.2 di ieri.
Bisognerebbe comparare le note delle due versioni.
Se più tardi ho tempo lo faccio

redpepper ha scritto: ↑26 nov 2024, 21:46 È la versione per chi usa la 5.1 non un aggiornamento della 5.2

[Security Updates]
- Applied multiple security updates to further enhance system security.

[Enhancement]
Control Panel
- To optimize storage stability, disk auto recovery is now enabled by default for device models that support this feature. Users can change this setting by going to "Control Panel > System > Hardware > General".
- Added two enhancements to IP access protection:
(1) Improved security: IP access protection is now enabled by default for SMB protocols.
(2) Greater flexibility: You can now select ""Exclude internal IP addresses"" to ignore failed login attempts from internal IP addresses.
To configure these settings, go to ""Control Panel > System > Security > IP Access Protection"".
Storage & Snapshots
- Optimized the performance of mounting snapshots.

[Fixed Issues]
- Resolved an issue where after restarting the NAS under certain conditions, QVR Pro would become disabled and could not be started.
- Resolved an issue where a user group could not be created normally if the "Description" field included certain special characters.
- Fixed an issue where a manually installed third-party app might connect via HTTP instead of HTTPS as expected.
- Improved the scroll bar user experience in the "Edit Shared Folder Permission" window in "Control Panel > Privilege > Shared Folders > Shared Folder".
- Fixed an issue where the syslog server on the NAS could not receive certain log messages from a third-party syslog generator.
- Fixed an issue where some users had to manually log in to Qfile Pro for Android and go through 2-step verification every time after closing and then reopening the app.
- Resolved an issue where some users could not mount an external drive formatted in EXT2.
- Addressed an issue where some users encountered slow read and write speeds under certain conditions.
- Fixed an issue in Storage & Snapshots where the "Snapshot Manager" window could only show two pages of files in a folder that actually contained more files.
- Resolved an issue in Storage & Snapshots where the volume management window displayed incorrect sizes for shared folders.
- Fixed a rare issue in iSCSI & Fibre Channel where the username and password fields in "Modify an iSCSI Target > iSCSI Target" might temporarily disappear under certain conditions.
- Fixed an issue where users could not open Security Center after unlocking an SED secure storage pool or volume.
- Resolved a rare issue where the NAS might stop responding after the user performed certain actions on a Samba shared folder.
- Fixed an issue in Storage & Snapshots where after removing a Thunderbolt card from the TVS-1582TU, the NAS diagram on the "Disks/VJBOD" page would display incorrect disk locations.
- Fixed an issue on the TS-1635AX where some users could not successfully update the firmware.
- Resolved a rare issue where after enabling SMB access logs, accessing a NAS shared folder via SMB from Windows might take a long time.
- Fixed an issue where Network & Virtual Switch could not display the up and down speeds of VLAN interfaces on trunk ports.
- Improved the NFS permissions mechanism.
- Fixed an issue where a trunk port failover caused the NAS to incorrectly show an iSCSI LUN to be offline and the LUN's target IQN to change.

[Other Changes]
App Center
- Starting from now, to access the beta versions of QNAP applications, please join the QNAP App Beta Program by going to "App Center > Settings > General".