ho un qnap ts-439 pro, incautamente mi taglierei le mani, alla voce sicurezza ho ripristinato il certificato predefinto e chiave privata.
risultato, in gestione archivi il raid5 e presente, ma me lo da in stato non montato....... aiutooooooooooooooo
ho provato a collegarmi in ssh al nas:
cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath]
md0 : active raid5 sda3[0] sdd3[3] sdc3[2] sdb3[1]
5855836800 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU]
md4 : active raid1 sdd2[4](S) sdc2[3](S) sdb2[2] sda2[0]
530128 blocks super 1.0 [2/2] [UU]
md13 : active raid1 sdc4[0] sda4[3] sdd4[2] sdb4[1]
458880 blocks [4/4] [UUUU]
bitmap: 0/57 pages [0KB], 4KB chunk
md9 : active raid1 sdc1[0] sda1[3] sdd1[2] sdb1[1]
530048 blocks [4/4] [UUUU]
bitmap: 1/65 pages [4KB], 4KB chunk
unused devices: <none>
ho provato a fare il mount:
mount -t ext4 /dev/md0 /share/MD0_DATA
mount: wrong fs type, bad option, bad superblock on /dev/md0,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
inviando il comando:
dmesg
120
[ 46.858311] md13: unknown partition table
[ 48.207269] kjournald starting. Commit interval 5 seconds
[ 48.251435] EXT3-fs (md9): using internal journal
[ 48.255620] EXT3-fs (md9): mounted filesystem with writeback data mode
[ 73.881985] kjournald starting. Commit interval 5 seconds
[ 73.956201] EXT3-fs (md9): using internal journal
[ 73.960419] EXT3-fs (md9): mounted filesystem with ordered data mode
[ 124.255138] kjournald starting. Commit interval 5 seconds
[ 124.333219] EXT3-fs (md13): using internal journal
[ 124.337477] EXT3-fs (md13): mounted filesystem with writeback data mode
[ 148.157231] cryptodev: driver 0.9 loaded.
[ 148.191599] usbcore: registered new interface driver usbhid
[ 148.196524] usbhid: USB HID core driver
[ 148.210001] Register ICH/PCH RTC driver.
[ 148.224398] iTCO_vendor_support: vendor-support=0
[ 148.233159] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 148.239535] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0860)
[ 148.245592] iTCO_wdt: initialized. heartbeat=120 sec (nowayout=0)
[ 148.258406] usbcore: registered new interface driver usblp
[ 148.275571] e1000e: Intel(R) PRO/1000 Network Driver - 2.4.14-NAPI
[ 148.281201] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 148.285974] e1000e 0000:01:00.0: Disabling ASPM L0s L1
[ 148.290535] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 148.295132] e1000e 0000:01:00.0: irq 44 for MSI/MSI-X
[ 148.295155] e1000e 0000:01:00.0: irq 45 for MSI/MSI-X
[ 148.295177] e1000e 0000:01:00.0: irq 46 for MSI/MSI-X
[ 148.401988] e1000e 0000:01:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:08:9b:bd:95:24
[ 148.406999] e1000e 0000:01:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 148.411483] e1000e 0000:01:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[ 148.422581] e1000e 0000:02:00.0: Disabling ASPM L0s L1
[ 148.427288] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 148.432111] e1000e 0000:02:00.0: irq 47 for MSI/MSI-X
[ 148.432134] e1000e 0000:02:00.0: irq 48 for MSI/MSI-X
[ 148.432156] e1000e 0000:02:00.0: irq 49 for MSI/MSI-X
[ 148.544409] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:08:9b:bd:95:25
[ 148.550474] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection
[ 148.556400] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[ 148.567449] jnl: driver (lke_9.2.0 QNAP, LBD=ON) loaded at f8836000
[ 148.577736] ufsd: module license 'Commercial product' taints kernel.
[ 148.582549] Disabling lock debugging due to kernel taint
[ 148.590737] ufsd: driver (lke_9.2.0 QNAP, build_host("BuildServer47-1"), acl, ioctl, bdi, sd2(0), fua, bz, rsrc) loaded at f8933000
[ 148.590746] NTFS support included
[ 148.590750] Hfs+/HfsJ support included
[ 148.590753] optimized: speed
[ 148.590756] Build_for__QNAP_Atom_x86_k3.4.6_2014-12-15_lke_9.2.0_r245986_b56
[ 148.590761]
[ 148.673380] fnotify: Load file notify kernel module.
[ 149.796495] usbcore: registered new interface driver snd-usb-audio
[ 149.810809] usbcore: registered new interface driver snd-usb-caiaq
[ 149.830211] Linux video capture interface: v2.00
[ 149.866600] usbcore: registered new interface driver uvcvideo
[ 149.873111] USB Video Class driver (1.1.1)
[ 150.061394] 8021q: 802.1Q VLAN Support v1.8
[ 163.112996] kjournald starting. Commit interval 5 seconds
[ 163.121180] EXT3-fs (md9): using internal journal
[ 163.126214] EXT3-fs (md9): mounted filesystem with ordered data mode
[ 168.380805] md: bind<sda2>
[ 168.389246] md/raid1:md4: active with 1 out of 1 mirrors
[ 168.395754] md4: detected capacity change from 0 to 542851072
[ 169.428905] md4: unknown partition table
[ 171.563181] Adding 530124k swap on /dev/md4. Priority:-1 extents:1 across:530124k
[ 176.206037] md: bind<sdb2>
[ 176.229886] RAID1 conf printout:
[ 176.229896] --- wd:1 rd:2
[ 176.229905] disk 0, wo:0, o:1, dev:sda2
[ 176.229914] disk 1, wo:1, o:1, dev:sdb2
[ 176.230118] md: recovery of RAID array md4
[ 176.235321] md: minimum _guaranteed_ speed: 5000 KB/sec/disk.
[ 176.240672] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 176.245940] md: using 128k window, over a total of 530128k.
[ 178.778390] md: bind<sdc2>
[ 180.977508] md: bind<sdd2>
[ 182.977064] md: md0 stopped.
[ 183.001740] md: md0 stopped.
[ 183.226696] md: bind<sdb3>
[ 183.231920] md: bind<sdc3>
[ 183.237061] md: bind<sdd3>
[ 183.242125] md: bind<sda3>
[ 183.248408] md/raid:md0: device sda3 operational as raid disk 0
[ 183.253075] md/raid:md0: device sdd3 operational as raid disk 3
[ 183.257598] md/raid:md0: device sdc3 operational as raid disk 2
[ 183.262038] md/raid:md0: device sdb3 operational as raid disk 1
[ 183.284102] md/raid:md0: allocated 67792kB
[ 183.288603] md/raid:md0: raid level 5 active with 4 out of 4 devices, algorithm 2
[ 183.293020] RAID conf printout:
[ 183.293026] --- level:5 rd:4 wd:4
[ 183.293034] disk 0, o:1, dev:sda3
[ 183.293040] disk 1, o:1, dev:sdb3
[ 183.293046] disk 2, o:1, dev:sdc3
[ 183.293051] disk 3, o:1, dev:sdd3
[ 183.293131] md0: detected capacity change from 0 to 5996376883200
[ 184.415275] md0: unknown partition table
[ 186.144882] md: md4: recovery done.
[ 186.231445] RAID1 conf printout:
[ 186.231454] --- wd:2 rd:2
[ 186.231463] disk 0, wo:0, o:1, dev:sda2
[ 186.231470] disk 1, wo:0, o:1, dev:sdb2
[ 186.250227] RAID1 conf printout:
[ 186.250234] --- wd:2 rd:2
[ 186.250240] disk 0, wo:0, o:1, dev:sda2
[ 186.250246] disk 1, wo:0, o:1, dev:sdb2
[ 186.250250] RAID1 conf printout:
[ 186.250255] --- wd:2 rd:2
[ 186.250260] disk 0, wo:0, o:1, dev:sda2
[ 186.250266] disk 1, wo:0, o:1, dev:sdb2
[ 188.292546] 8021q: adding VLAN 0 to HW filter on device eth0
[ 188.418774] 8021q: adding VLAN 0 to HW filter on device eth1
[ 191.817095] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 210.962643] e1000e 0000:01:00.0: eth0: changing MTU from 1500 to 8996
[ 214.673096] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 249.697587] Initiate iscsi target log successfully.
[ 249.724849] iscsi_log_rcv_msg: get log pid = 7081.
[ 257.211662] rule type=2, num=0
[ 257.547924] Loading iSCSI transport class v2.0-871.
[ 257.636214] iscsi: registered transport (tcp)
[ 257.706124] iscsid (7746): /proc/7746/oom_adj is deprecated, please use /proc/7746/oom_score_adj instead.
[ 260.062075] tun: Universal TUN/TAP device driver, 1.6
[ 260.068458] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 260.131404] PPP generic driver version 2.4.2
[ 260.253084] nf_conntrack version 0.5.0 (16089 buckets, 64356 max)
[ 260.360071] PPP MPPE Compression module registered
[ 260.389899] PPP BSD Compression module registered
[ 260.422106] PPP Deflate Compression module registered
[ 260.433097] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 270.829424] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 270.837541] NFSD: starting 90-second grace period
[ 292.806518] sysRequest.cgi[9750]: segfault at 18 ip b6f9fc2e sp bf92bbe4 error 6 in libc-2.6.1.so[b6f16000+12d000]
[ 1718.436940] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 1760.898861] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 1872.234822] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 2351.949132] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 2439.429208] EXT3-fs (md0): error: can't find ext3 filesystem on dev md0.
[ 2447.380937] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 3641.542190] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[ 3648.464399] EXT4-fs (md0): VFS: Can't find ext4 filesystem
[~] #
il log del problema..
aiuto vi prego, c'e' qualche possibilita di recuperare il contenuto degli HD in raid5, o ancora esiste un modo per riprare e fare di nuovo il mount del RAID5???????
Grazie a tutti.
mi sa che ho fatto un casino..........
Grazie ciao.
Gianluca
